Our products are to comply with environmental requirements in accordance with SONY code no. SS-00259 with restrictions of 10 harmful materials.
Features
Highly stable in auto-placement surface mounting application ‧ Compatible with both wave soldering and reflow soldering
| Size | L | W | T | C | D |
| 0201 | 0.60±0.03 | 0.30±0.03 | 0.23±0.03 | 0.15±0.05 | 0.15±0.05 |
| 0402 | 1.00±0.10 | 0.50±0.05 | 0.35±0.05 | 0.20±0.10 | 0.25±0.10 |
| 0603 | 1.60±0.10 | 0.80±0.10 | 0.45±0.10 | 0.25±0.15 | 0.30±0.15 |
| 0805 | 2.00±0.10 | 1.25±0.10 | 0.50±0.10 | 0.35±0.20 | 0.40±0.20 |
| 1206 | 3.10±0.10 | 1.55±0.10 | 0.55±0.10 | 0.45±0.20 | 0.40±0.20 |
| 1210 | 3.10±0.10 | 2.50±0.10 | 0.55±0.10 | 0.45±0.25 | 0.45±0.25 |
| 1218 | 3.10±0.10 | 4.60±0.10 | 0.55±0.10 | 0.45±0.25 | 0.45±0.25 |
| 1812 | 4.50±0.10 | 3.10±0.20 | 0.55±0.05 | 0.55±0.20 | 0.70±0.20 |
| 2010 | 5.00±0.20 | 2.50±0.15 | 0.55±0.10 | 0.60±0.25 | 0.50±0.25 |
| 1225 | 3.10±0.15 | 6.30±0.15 | 0.90±0.15 | 0.60±0.30 | 0.80±0.25 |
| 2512 | 6.35±0.20 | 3.10±0.15 | 0.55±0.10 | 0.60±0.25 | 0.60±0.25 |
| Type | RCTO1 | RCT02 | RCTO3 | RCT05 | RCT06 | RCT10 | RCT18 | RCT12 | RCT20 | RCT25 | RCT22 | |
Size | 0201 | 0402 | 0603 | 0805 | 1206 | 1210 | 1812 | 1218 | 2010 | 2512 | 1225 | |
Power Rating at 70℃ | 1/20W | 1/16W | 1/10W | 1/8W | 1/4W | 1/3W | 1/2W | 1W | 3/4W | 1W | 2W | |
Max RCWV | 25V | 50V | 75V | 150V | 200V | 200V | 200V | 200V | 200V | 200V | 200V | |
Max Overload Voltage | 50V | 100V | 150V | 300V | 400V | 400V | 400V | 400V | 400V | 400V | 400V | |
Jumper<50mΩ | 0.5A | 1A | 1A | 2A | 2A | 2A | 2A | 2A | 2A | 2A | 10A | |
Operating Temperature Range | -55～+155°℃ | |||||||||||
Standard Resistance Range | 0Ω | 0~50mO | ||||||||||
| ±1%(E-96) | 12~10MO | 12～10MΩ | 10Ω~ 20KΩ | |||||||||
| ±5%(E-24) | 12~10MΩ | 12~22MΩ | ||||||||||
| ITEM | SPECIFICATION | TEST METHOD |
Solderability | Over 95%of termination must be covered with solder | JIS C 52014.17/MIL-STD-202G METHOD 208H / IEC 60115-14.17 Reflow Soldering:Bath temperature:(235±5)℃,Immersion time:(2±0.5)s WAVE Soldering:Bath temperature:(270±10)℃,Immersion time:(2±0.5)s |
Resistance to Solder Heat | J、G:△R≤±(1%+0.05Ω) F:△R≤±(0.5%+0.05Ω) No mechanical damage | JIS C 52014.18/MIL-STD-202G METHOD 210F/IEC 60115-14.18 The temperature of the solder bath shall be (260±5)°℃,The immersion time shall be(5±0.5)s or(10±1)s as prescribed by the detail specification |
Temperature Coefficient of Resistance (TCR) | 0402&0201: 12~102;>3.3M:±400ppm/℃ 102(excluding 102)~3.3M: ±200ppm/℃ (0603 or above): 1Ω~10Ω;>1M:±200ppm/℃ 102(excluding102)~1M: ±100ppm/℃ | JIS C 52014.8/MIL-STD-202G METHOD 304/IEC 60115-14.8 The temperature characteristic or temperature coefficient of resistance is not specified for resistance values of less than 5R owing to difficulty of accurate measurement |
Short Time Overload | J、G:△R≤±(2%+0.05Q) F:△R≤±(1%+0.05Ω) | JIS C 52014.13/IEC 60115-14.13 2.5×Rated voltage or Max.Overload Voltage for 5 sec measure resistance after 30 minutes |
Load Life Humidity | J、G:△R≤±(3%+0.05Ω) F:△R≤±(1%+0.05Ω) | JIS C 52014.24/MIL-STD-202G Method 106G/IEC 60115-14.24 Maintain the temperature of the resistor at 40±2℃ and 90～95%RH with the rated voltage applied.Cycle ON for 1.5 hours and OFF for 0.5 hour for1000+48/-0 hours.After 1～4 hour,measure the resistance value |
Load Life | J、G:△R≤±(3%+0.05Ω) F:△R≤±(1%+0.05Ω) | JIS C 52014.25/MIL-STD-202G Method 108A/IEC 60115-14.25 70±2℃,Max.working voltage for 1000 hrs with 1.5 hrs “ON”and 0.5 hrs “OFF”. |
Temperature Cycle | J、G:△R≤±(1%+0.05Ω) F:△R≤±(0.5%+0.05Ω) No mechanical damage | JIS C 52014.19/MIL-STD-202G Method 107G /IEC 60115-14.19 Repeat 5 cycles as follows -65℃(30 min.)+25℃(2～3 min.)+125℃(30 min.)+25°℃(2～3 min.) |
Insulation Resistance | Between termination and coating must be over 1000MΩ | JIS C 52014.6/MIL-STD-202G Method 302/IEC 60115-14.6 Test voltage:100±15V |
| JIS C 52014.33/MIL-STD-202G Method 211A/IEC 60115-14.33 | ||
| J、G:△R≤±(1%+0.05Ω) | Resistance change after bended on the 90mm PCB | |
| Bending | F:△R≤±(0.5%+0.05Q) | Bend:3mm for 0201、0402、0603、0805、1206 |
| Strength | No mechanical damage | 2mm for 1210、1812 、1218、1225 |
| mm for 2010、2512 |
Home About HKR Products Application Service Resources News Contact Us